PE1900
8Tilting the Display The monitors have a tilt feature that allows you to tilt the display back and forth to find the most comfortable viewing positio
9The table in “Video Mode” on page 27 shows the image refresh rates supported by the display at different screen resolution. Although your LCD monito
10Note: If the screen is still dirty, you can dampen the cloth with several drops of distilled water. Make sure the LCD panel is completely dry befor
11Adjusting Your Display This chapter contains information about how to change display settings for your LCD Monitor. It is designed with an OSD menu
12Item Description Auto Adjust the “Auto Setup”. See “Adjusting Auto Setup” on page 12. Management Open the “Management” submenu to select Brightnes
13 3. Use ‘Select’ button to select and execute the Auto Setup function. After the execution of the Auto Setup function, it will show the following
14 3. Use ‘Select’ key to enter the “Management” Submenu. This activates four items for adjustment. If ‘Brightness’ is selected, use ‘Up (△)’ or ‘Do
15responds accordingly. If ‘V. position’ is selected, use ‘Up (△)’ or ‘Down (▽)’ buttons to adjust the setting of the vertical position of the image
16Adjusting the “Clock/Phase” Submenu Follow the steps below to adjust the “Clock/Phase” submenu: 1. Activate the OSD “Main Menu”. 2. Use ‘Up (△)’
17 Adjusting the “Color” Submenu Follow the steps below to adjust the “Color” submenu: Activate the OSD “Main Menu”. 1. Use ‘Up (△)’ (or ‘Down (▽)’)
18 Note: As you choose an item, your screen immediately updates to reflect this setting. Selecting ‘Black Level Adjust’ activates the “Back Level Adj
19 Adjusting the “OSD Display” submenu Follow the steps below to adjust the OSD Horizontal and Vertical positions: 1. Activate the OSD “Main Menu”.
20 Select ‘Exit’ to exit the “OSD Display” submenu and return to the “Main Menu”. Adjusting the Factory Recall To recall factory settings back you s
21Selecting your preferred Language Follow the steps below to select one of the five languages: 1. Activate the OSD “Main Menu”. 2. Use ‘Up (△)’ (
22 Using the Direct Keys There are two direct keys that function while OSD “Main Menu” is inactivated: “Auto-Setup” and “Brightness.” Using the “Auto
23If the image requires further adjustment, choose No, and the ‘Phase’ bar is activated for further manual adjustment. Adjust the phase using ‘Up (△)
24Troubleshooting This chapter contains information about how to troubleshoot your LCD Monitor. If you have tried all of the items listed below, plea
25E. The image is very unstable. 1. Set your PC to a supported video mode, preferably 1280 x 1024 at 60 Hz. See “Setting the Video Mode” on page 8.
26Technical Information This chapter contains technical information about your LCD Monitor. Display Information LCD Module 19-in, active matrix TFT,
27Video Modes Your LCD monitor supports the following industry-standard combinations of screen resolution and refresh rates. Other combinations are p
1Contents Introduction ...2 Features ...
28 Regulatory Information Agency Approvals EuropeanUSA Japan Others CE UL Safety CSA Emissions FCC Class B .DOC Immunit
PLANAR SYSTEMS, INC. Customer Servicesupport: http://planar.custhelp.comemail: [email protected]: 1-866-PLANAR-1 (1-866-752-6271)hou
2Introduction The PE1900 LCD monitor has a 19-inch active matrix TFT (thin film transistor) liquid crystal display module. It is designed for use wit
3If any of the following conditions occur, unplug the display and contact qualified service personnel: Ö The power cord or plug is frayed or damaged
4Installation Please follow the instructions in this chapter to install your LCD Monitor. Note: Before connecting your display, first read through th
5The functions of the three control buttons which are located at the lower left side of the front panel of your display are described as below: Butto
64. Plug the analog video signal cable into the Analog Video Input port on the back of the display (as shown above). 5. Connect the other end of the
7Using Your Display This chapter contains information about using your LCD Monitor. Turning the Display On and Off Use the power button located at th
Comments to this Manuals